HANLEI CO₂ Laser Cutting Machine
User Manual
Manufacturer: Dongguan Hanlei Laser Equipment Technology Co., Ltd.
Brand: HANLEI
Product: CO₂ Laser Cutting and Engraving Machine
Important Notice
Please read this manual carefully before installing, operating, or maintaining the machine.
This manual provides general operating instructions for HANLEI CO₂ laser cutting machines. Machine appearance, electrical configuration, accessories, control systems, and technical specifications may vary depending on the model. The actual machine and its supplied documentation shall prevail.
Only trained and authorized personnel should install, operate, maintain, or service the equipment.
Chapter 1. Safety Precautions
1.1 General Safety Requirements
Before operating the machine, users must carefully read this manual and all relevant operating instructions. All operating procedures must be followed strictly. Untrained personnel are prohibited from starting or operating the machine.
This machine incorporates a Class 4 laser source, which produces high-intensity laser radiation. Direct or reflected laser exposure can cause serious eye and skin injuries and may create fire hazards.
Potential hazards include:
Ignition of nearby combustible materials.
Generation of secondary radiation, smoke, fumes, and potentially toxic or hazardous gases depending on the processed material.
Serious personal injury caused by direct or reflected laser radiation.
The installation area must be equipped with suitable fire-fighting equipment. Do not store flammable or explosive materials near the machine or on the working platform. Ensure adequate ventilation and exhaust extraction. Unauthorized personnel must keep away from the equipment during operation.
Processed materials and all emissions generated during processing must comply with applicable local laws, regulations, and environmental requirements.
Laser processing may involve potential risks. Users must evaluate whether the selected material is suitable for laser processing before operation. Never process unknown materials without confirming their safety and compatibility.
The machine contains high-voltage electrical components and other potentially hazardous parts. Do not open, dismantle, or repair internal components unless you are an authorized and qualified service technician.
The machine must be continuously supervised while operating. Never leave the equipment unattended. Before leaving the machine, stop the operation and disconnect the power according to the approved shutdown procedure.
Never open protective covers, access panels, or machine enclosures while the equipment is operating.
The laser cutting machine and all associated electrical equipment must be properly grounded before use.
Do not place unrelated highly reflective or diffusely reflective objects inside the machine. Uncontrolled reflections may direct laser radiation toward people or combustible materials.
Operators must continuously monitor machine operation. If an abnormal condition occurs, stop the machine immediately and disconnect the power using the appropriate emergency shutdown procedure. Take corrective action only after the equipment has been made safe.
The installation environment should be dry, clean, and free from excessive vibration, strong electrical interference, and strong magnetic interference.
Recommended environmental conditions:
Operating temperature: 5–40°C
Relative humidity: 5–95%, non-condensing
Keep the machine away from electrical equipment that is sensitive to electromagnetic interference. The machine may generate electromagnetic interference that affects nearby equipment.
Electrical supply requirements:
Input voltage: AC 220V
Frequency: 50Hz
Reference rated power: 1250W
Actual power consumption varies by machine model and configuration. Do not operate the machine if the supply voltage is unstable or incompatible with the machine's specified electrical requirements.
1.2 Laser Radiation Safety
Never look directly into the laser beam or its reflected beam.
Never operate the laser with protective covers or safety interlocks bypassed.
Use laser safety eyewear specifically rated for the laser wavelength and optical density required by the equipment.
Keep the laser processing area enclosed and restrict access during operation.
Ensure that suitable fire protection and smoke extraction systems are available.
Never leave combustible materials near the processing area.
Do not process materials that may release hazardous gases without confirming their composition and providing suitable extraction.
Only trained personnel may perform laser optical alignment or maintenance.
Warning: The CO₂ laser source operates at approximately 10.6 μm (10,600 nm). Standard visible-light protective eyewear does not provide adequate protection against this wavelength.
1.3 Electrical Safety
The machine operates with high-voltage laser power supply components. Improper wiring, grounding, or maintenance may result in electric shock, fire, or equipment damage.
Electrical installation must be performed by a qualified electrician.
The machine must be connected to a reliable protective earth.
Never touch high-voltage terminals or wiring while the equipment is energized.
Disconnect and isolate the power supply before maintenance.
Verify that electrical connections and insulation are in good condition before operation.
Chapter 2. Precautions Before First Startup
Before energizing the laser cutting machine for the first time, check the following items:
Confirm that the input power supply meets the machine requirements: AC 220V, 50Hz, or the voltage specified on the machine nameplate.
Check that all electrical connectors and cables are securely connected. Pay particular attention to the laser tube high-voltage connection. High-voltage terminals must have appropriate insulation and protection.
Ensure that both the laser machine and the connected computer equipment are properly grounded.
Confirm that the water inlet and outlet hoses are correctly connected and that the cooling water can circulate smoothly.
Check that the air compressor and air hoses are properly connected. Confirm that the air-assist system supplies air normally.
Remove all unrelated objects from the machine working platform.
Check that the exhaust fan and extraction duct are correctly installed and operating.
Confirm that all protective covers, safety devices, and emergency stop functions are in place.
Only after all checks have been completed and verified should the machine be powered on.
The manufacturer shall not be responsible for losses or damage caused by improper installation, misuse, or failure to follow the safety instructions in this manual.
Chapter 3. Machine Appearance and Standard Accessories
3.1 Machine Appearance
The machine's external appearance may vary depending on the model and configuration. Please refer to the actual equipment supplied.
Main machine components:
Machine body and frame
Laser cutting gantry
Laser cutting head
Working platform
Electrical control cabinet
Control panel
Laser tube installation area
Cooling and ventilation connections
3.2 Standard Accessories
The standard accessories may vary depending on the machine configuration.
| No. | Accessory | Description |
|---|---|---|
| 1 | Laser power supply | Provides electrical power to the laser tube |
| 2 | Water hoses, air hoses, air pump and water pump | Cooling water circulation and air assistance |
| 3 | Exhaust fan, exhaust duct and clamps | Smoke and fume extraction |
| 4 | CO₂ laser tube | Laser source |
| 5 | Temperature-controlled water tank | Laser tube cooling system |
| 6 | Working platform accessories | Honeycomb panels (large and small openings), grid panels and knife-strip tables |
Please check all accessories against the packing list before installation.
Chapter 4. Machine Installation
4.1 System Overview
A complete laser cutting system generally consists of:
Laser cutting machine main unit
Laser power supply
Exhaust fan
Air compressor
Water tank or cooling unit
Exhaust duct
Data transmission cable
Computer and related software
Depending on production requirements, users may also need to prepare a computer, printer, scanner, or other auxiliary equipment.
4.2 Installing the CO₂ Laser Tube
The CO₂ glass laser tube is fragile and may be damaged by impact or improper handling. For transportation safety, the laser tube may be packed separately.
Install the laser tube before commissioning the machine.
Installation Procedure
Locate the laser tube compartment at the rear of the machine.
Open the laser tube protective cover.
Identify the laser tube support brackets.
Carefully place the laser tube onto the designated supports.
Position the laser output aperture (negative electrode end) toward Mirror No. 1.
Maintain the installation distance specified for the machine. The reference distance in the original configuration is approximately 10 mm between the tube output end and Mirror No. 1.
Secure the tube using the supplied support straps and fasteners.
Important Installation Notes
Do not overtighten the support straps. Excessive pressure may damage the glass tube.
Position the cooling water inlet at the lower side of the tube body where required by the tube design.
Ensure that the tube is properly supported and cannot move during machine operation.
Avoid impact, bending, or excessive mechanical stress on the tube.
Connecting the Cooling Water Hoses
Connect the water inlet hose to the cooling water inlet at the negative electrode end of the laser tube.
Connect the water outlet hose to the corresponding outlet.
Secure all hose connections to prevent leakage.
Arrange the hoses neatly without kinks, sharp bends, or compression.
Warning: Incorrect water connections or restricted water flow may cause overheating and permanent laser tube damage.
4.3 Installing the Laser Power Supply
The laser power supply is normally installed inside the electrical compartment at the rear of the machine.
The high-voltage connection between the laser power supply and the laser tube must only be installed by a qualified technician.
Installation Requirements
Verify the positive and negative terminals against the wiring diagram supplied with the specific machine.
Use the original high-voltage connectors and insulation components.
Ensure that high-voltage cables are properly insulated and secured.
Connect the AC 220V input cable and control signal cable according to the machine wiring diagram.
Check all connections before closing the electrical compartment.
High-Voltage Warning: The laser power supply can retain dangerous electrical energy even after the machine has been switched off. Do not touch or disconnect high-voltage wiring unless the equipment has been properly isolated and verified safe by a qualified technician.
Never energize the machine with exposed high-voltage connections.
4.4 Installing the Water Cooling System
The water cooling system removes heat generated by the laser tube.
Installation Procedure
Fill the water tank with clean, suitable cooling water according to the cooling system manufacturer's instructions.
Connect the cooling unit outlet to the machine water inlet.
Connect the machine water outlet to the cooling unit return inlet.
Check that all water hoses are securely connected.
Start the cooling system according to its operating instructions.
Confirm that water circulates smoothly through the laser tube and that there are no leaks or trapped air pockets.
Water Protection Function
The machine may be equipped with a water-flow protection sensor.
If the water flow becomes insufficient or the cooling system malfunctions, the protection system may prevent laser output to protect the laser tube.
During daily operation, check the cooling unit, water level, water flow, hose condition, and water quality.
Never operate the laser tube without confirmed cooling water circulation.
4.5 Installing the Air Compressor
The air-assist system supplies compressed air to the laser cutting head.
Installation Procedure
Connect the air compressor outlet to the machine air inlet using the supplied air hose.
Secure the hose connections.
Start the air compressor.
Confirm that air is discharged normally from the laser cutting head nozzle.
Functions of Air Assistance
Compressed air performs several important functions:
Helps keep the cutting nozzle and optical components cleaner.
Removes smoke and debris from the cutting area.
Helps reduce the risk of material ignition during suitable cutting operations.
Improves cutting performance for compatible materials.
Maintenance Note: Check the air hose regularly. Kinked, damaged, or leaking hoses may reduce airflow and increase the risk of poor cutting quality or fire.
4.6 Installing the Exhaust Fan
The exhaust system removes smoke, fumes, and processing residues generated during laser cutting.
Installation Procedure
Connect the exhaust duct to the fan inlet or outlet as indicated by the fan design.
Route the exhaust duct to a suitable outdoor discharge location or approved extraction system.
Secure all duct connections using the supplied clamps.
Connect the fan power cable according to the electrical wiring diagram.
Start the exhaust system and verify that airflow is adequate.
The exhaust system must be suitable for the processed material and comply with local environmental and workplace safety requirements.
4.7 Protective Earth Grounding
The laser machine uses a high-voltage laser excitation system. Reliable protective grounding is essential for electrical safety and equipment stability.
The electrical supply system must comply with applicable local electrical codes and safety standards.
Electrical Connection Identification
| Symbol | Description | Function |
|---|---|---|
| L | Live | AC power supply conductor |
| N | Neutral | AC power return conductor |
| E / PE | Protective Earth | Safety grounding conductor |
The protective earth connection must be connected to the designated grounding terminal of the machine.
Grounding Requirements
All exposed conductive machine enclosures must be connected to protective earth.
The power supply must include a properly installed protective grounding conductor.
Protective grounding continuity and resistance must be verified by a qualified electrician using appropriate test equipment.
The grounding arrangement must meet local electrical regulations and the machine manufacturer's requirements.
The original equipment documentation specifies a grounding resistance reference below 5 Ω. The actual acceptance value must be confirmed against the applicable electrical standard and installation conditions.
Important: Do not use improvised grounding arrangements. Grounding electrodes, conductors, connections, and testing must be designed and installed by a qualified electrical professional.
Poor grounding may cause electrical faults, equipment malfunction, electric shock, or fire.
Chapter 5. Power-On and Shutdown Procedures
5.1 Startup Sequence
The original control configuration uses the following general startup sequence:
Main power switch
Main control board
Power distribution strip or auxiliary power switch
Machine lighting
Laser system
The exact sequence may vary depending on the machine's electrical configuration. Follow the labels and startup instructions supplied with the actual machine.
Before Starting
Confirm that:
The cooling system is operating normally.
The exhaust fan is working.
The air-assist system supplies air correctly.
The working area is clear.
All protective covers are closed.
No abnormal condition is present.
5.2 Shutdown Sequence
The original control configuration uses the following general shutdown sequence:
Laser system
Auxiliary power switch or power distribution strip
Main control board
Machine lighting
Main power switch
Allow the laser output to stop and follow the cooling system manufacturer's recommended post-operation procedure before disconnecting cooling power.
Do not disconnect the cooling system immediately after laser operation if the laser tube requires continued cooling.
Chapter 6. Laser Optical Path Alignment and Focus Adjustment
6.1 Optical Path Overview
The CO₂ laser beam is directed through a series of reflective mirrors and a focusing lens before reaching the workpiece.
A typical three-mirror optical system consists of:
Mirror No. 1: Located near the laser tube output.
Mirror No. 2: Mounted at the end of the moving gantry.
Mirror No. 3: Mounted near the laser head.
Focusing lens: Installed inside the lower section of the laser head.
Correct optical alignment is important for consistent cutting performance.
6.2 Optical Alignment Safety
Warning: Optical alignment is a hazardous laser operation. It must only be performed by trained and authorized laser service personnel.
Before alignment:
Restrict access to the machine area.
Verify that all protective measures are in place.
Use wavelength-appropriate laser safety equipment.
Use the lowest effective laser output permitted by the manufacturer's approved alignment procedure.
Never place hands or any part of the body in the beam path.
Never look into the laser output aperture or reflected beam.
Do not bypass safety interlocks or operate the machine with uncontrolled exposed beam paths.
The original machine documentation describes alignment using test marks on suitable target materials. This procedure must only be performed under an approved service procedure with appropriate beam containment and safety controls.
If you are not trained in laser optical alignment, contact HANLEI technical support or an authorized service technician.
6.3 General Alignment Objectives
The alignment process should verify the following:
The laser beam is correctly directed toward the center of Mirror No. 1.
The beam remains correctly aligned as the gantry moves across its travel range.
The beam enters the laser head through the designated optical aperture.
The beam remains correctly positioned at different points across the working platform.
The beam is correctly centered through the focusing assembly.
If alignment errors are found, the machine must be adjusted according to the model-specific optical alignment procedure.
Do not make random adjustments to the laser tube or mirror mounts.
6.4 Laser Tube Position Adjustment
The original machine design allows adjustment of the laser tube position to correct certain beam alignment deviations.
Any adjustment must be performed by a qualified technician after the laser system has been safely isolated and the alignment procedure has been reviewed.
Do not adjust the laser tube while the machine is energized or while the beam path is exposed.
6.5 Restoring Protective Covers
After alignment:
Reinstall all laser tube protective covers.
Reinstall all optical protection components.
Verify that all fasteners are secure.
Confirm that safety interlocks function correctly.
Perform a final safety inspection before returning the machine to service.
6.6 Focus Adjustment
Correct focusing is important for cutting quality.
The machine may be supplied with a dedicated focus gauge. Use the focal distance specified for the actual laser head and lens configuration.
General Focus Adjustment Procedure
Place the workpiece or a suitable test material on the working platform.
Position the laser head above the material.
Use the supplied focus gauge or approved focusing method to set the specified distance between the nozzle or lens reference point and the material surface.
Secure the laser head according to the machine design.
Verify the focus setting before beginning production.
The focal distance depends on the installed lens and laser head configuration. Always use the value supplied with the machine.
Focus Verification
Focus can be verified using an approved test procedure performed by trained personnel.
Do not use prolonged manual laser firing or uncontrolled exposure to determine the focal position.
Chapter 7. Control Panel Operation
7.1 Control Panel Overview
HANLEI laser cutting machines may use different control systems depending on the model.
The following section describes a representative touch-style control panel commonly used on CO₂ laser cutting machines.
The panel generally includes:
16 function keys
LCD display
Machine status information
Processing file information
Speed and laser power settings
The actual control panel layout may vary.
7.2 Common Control Panel Functions
| Function Key | Description |
|---|---|
| Reset | Initializes the control system and returns the machine to its reference position |
| Pulse / Laser Test | Activates a laser test pulse when the system is in an allowed state |
| Max Power | Sets or adjusts maximum laser power |
| Min Power | Sets or adjusts minimum laser power |
| Frame | Runs the job boundary preview |
| File | Opens the stored processing file list |
| Origin / Position | Sets the processing origin |
| Exit | Cancels the current operation or returns to the previous interface |
| Enter / Confirm | Confirms a selection or parameter change |
| Start / Pause | Starts or pauses the current processing job |
| Up | Moves the laser head or selection upward |
| Down | Moves the laser head or selection downward |
| Left | Moves the laser head or selection to the left |
| Right | Moves the laser head or selection to the right |
| Z/U | Provides auxiliary axis or extended function control |
The exact functions of Max Power, Min Power, and Z/U may vary according to the controller model.
7.3 Display Information
The LCD screen may display:
Processing file name
Current processing speed
Laser power settings
System initialization status
Standby status
Processing status
Pause status
Error or warning information
7.4 Machine Origin and Processing Origin
Machine Origin
The machine origin is the reference position used by the motion control system. In the original machine configuration, this position is located at the upper-right corner of the working area.
The machine normally returns to this position during startup or reset.
Processing Origin
The processing origin is the starting position selected by the operator for a specific cutting or engraving job.
After homing, the laser head may move to the previously defined processing origin.
The actual machine origin direction and location must be verified against the machine configuration.
7.5 Reset Function
The Reset key initializes the control system.
When Reset is pressed:
The control system restarts its initialization process.
The machine performs its homing operation.
The display indicates that the machine is returning to its reference position.
After homing, the laser head may return to the previously defined processing origin.
If the previous job was interrupted by a power failure, some controllers may provide a power-off recovery or resume function.
The availability and behavior of this function depend on the controller model and job file.
Important: Before resuming an interrupted job, verify the material position, machine origin, cutting path, and workpiece condition. Do not resume if the workpiece has moved or the machine position is uncertain.
7.6 File Function
The File key opens the processing file menu.
Typical operation:
Press File.
Select the internal memory file list.
Use the Up and Down keys to browse stored files.
Select the required processing file.
Press Enter to confirm.
The supported file formats depend on the controller and connected software.
7.7 Exit Function
The Exit key cancels the current operation or returns the controller to the previous interface.
It may be used to:
Cancel parameter changes.
Cancel file selection.
Exit the current job in standby or pause mode.
Return to the main operating interface.
The exact behavior depends on the current controller state.
7.8 Enter / Confirm Function
The Enter key confirms the selected operation.
It may be used when:
Saving processing speed settings.
Confirming minimum or maximum laser power.
Selecting a processing file.
Confirming system parameter changes.
7.9 Pulse / Laser Test Function
The Pulse key activates a laser test pulse when the controller permits laser output.
This function must only be used by trained operators under approved laser safety conditions.
Never activate the laser when the beam path is exposed or when people may be exposed to direct or reflected radiation.
7.10 Start / Pause Function
The Start/Pause key switches the controller between processing and pause states.
When the machine is in standby, the controller may start the selected job.
During processing, pressing the key pauses the current job.
Pressing it again may resume the job from the paused position.
Follow the controller-specific operating instructions.
7.11 Direction Keys
The direction keys are used for manual positioning and menu navigation.
| Key | Function |
|---|---|
| Up | Move the laser head upward |
| Down | Move the laser head downward |
| Left | Move the laser head left |
| Right | Move the laser head right |
The directional definitions in this manual are based on the operator facing the working platform.
Forward / Up: Gantry moves away from the operator.
Backward / Down: Gantry moves toward the operator.
Left: Operator's left side.
Right: Operator's right side.
Chapter 8. Daily Maintenance and Troubleshooting
Correct operation and regular maintenance are essential for stable machine performance and long service life.
8.1 Cooling Water Replacement and Water Tank Cleaning
Recommended maintenance interval: Check the cooling water regularly. The original machine documentation recommends weekly cleaning of the water tank and replacement of the circulating water. Actual intervals should follow the cooling system and laser tube manufacturer's requirements.
Important Requirements
Ensure that the laser tube is completely filled with circulating cooling water before operation.
Use clean, suitable cooling water, normally purified or deionized water as specified by the cooling system manufacturer.
Keep the cooling water temperature within the recommended operating range.
The original documentation recommends maintaining water temperature below 35°C.
If the water temperature exceeds the recommended limit, stop processing and restore proper cooling before restarting.
For higher-power configurations or demanding production environments, use a suitable industrial water chiller.
Water Tank Cleaning Procedure
Stop the machine and disconnect the power according to the approved maintenance procedure.
Allow the cooling system to become safe for maintenance.
Disconnect the water hoses as required.
Drain the cooling water into a suitable container.
Remove the water pump if applicable.
Clean accumulated dirt and deposits from the water tank and pump.
Refill the tank with suitable cooling water.
Reconnect all hoses and fittings.
Restore the cooling system and verify normal circulation.
Check for leaks and confirm that the laser tube is properly filled with water.
Do not operate the laser tube until normal cooling circulation has been confirmed.
8.2 Exhaust Fan Cleaning
Long-term operation may cause dust and processing residues to accumulate inside the exhaust fan.
Accumulation may result in:
Reduced extraction performance
Increased operating noise
Poor smoke removal
Increased maintenance requirements
Cleaning Procedure
Stop the machine and isolate the electrical power.
Disconnect the exhaust ducts from the fan.
Inspect the fan housing and blades.
Remove accumulated dust and residues using suitable cleaning equipment.
Check the fan blades and housing for damage.
Reinstall the exhaust ducts securely.
Restore power and verify normal fan operation.
Do not operate the fan if the blades, housing, or electrical components are damaged.
8.3 Optical Lens Cleaning
Recommended maintenance interval: Inspect the optical components regularly. The original documentation recommends checking and cleaning them before daily operation when necessary.
The typical optical system contains:
Mirror No. 1
Mirror No. 2
Mirror No. 3
Focusing lens
Dust, smoke, and other contaminants may accumulate on optical surfaces. Contamination can reduce laser transmission and may damage the optical coating.
Cleaning Requirements
Switch off and isolate the machine before optical maintenance.
Allow optical components to cool.
Use approved optical cleaning materials and lens tissue.
Avoid touching optical surfaces directly with your fingers.
Do not apply excessive pressure.
Never use abrasive materials or unsuitable solvents.
Cleaning Procedure
Inspect each optical component for dust, smoke deposits, or contamination.
Clean accessible mirrors using suitable optical cleaning materials.
Remove optical components only when necessary and only if you are trained to do so.
Reinstall removed components in their original orientation.
Verify that all optical mounts are secure before returning the machine to service.
Important: The original optical configuration specifies that the focusing lens should be installed with its concave surface facing downward. Confirm the correct orientation against the actual lens design and laser head documentation before installation.
Do not force or rotate optical components in their mounts.
8.4 Linear Guide Rail Cleaning and Lubrication
Recommended maintenance interval: Approximately every two weeks, depending on operating conditions and manufacturer recommendations.
Required Materials
Clean, dry lint-free cloth
Suitable machine guide rail lubricant
Linear Guide Rail Maintenance
Switch off and isolate the machine.
Move the laser head to an accessible position using the approved manual positioning procedure.
Wipe dust and debris from the exposed guide rail surfaces.
Apply a small amount of suitable lubricant according to the guide rail manufacturer's recommendations.
Move the axis through its travel range using the approved procedure to distribute the lubricant.
Remove excess lubricant and inspect for abnormal wear.
Roller Guide Rail Maintenance
Isolate the machine power.
Open the designated maintenance access covers if required.
Inspect the guide rails and roller contact surfaces.
Remove dust and accumulated debris using a clean cloth.
Inspect the rollers for wear or damage.
Lubricate only the components specified by the manufacturer.
Do not apply excessive lubricant. Avoid lubricating belts, electrical components, or surfaces where lubricant may contaminate the processing area.
8.5 Optical Path Inspection
The optical path relies on the correct positioning of the reflective mirrors and focusing assembly.
Mechanical vibration, impact, or improper maintenance may cause optical misalignment.
Inspection Requirements
Before production, operators should check:
Whether the optical components are clean.
Whether the mirror mounts are secure.
Whether the laser head and protective covers are correctly installed.
Whether cutting performance has changed abnormally.
Whether any signs of optical damage or contamination are present.
If optical misalignment is suspected, stop production and contact a trained laser service technician.
Refer to Chapter 6 for optical alignment safety requirements.
8.6 General Maintenance Checklist
| Maintenance Item | Recommended Frequency | Inspection |
|---|---|---|
| Cooling water level and circulation | Before each operation | Confirm normal water flow |
| Water hoses and connections | Regularly | Check for leaks, kinks, and damage |
| Exhaust fan and duct | Regularly | Check airflow and accumulated dust |
| Optical components | Before operation | Inspect for contamination or damage |
| Guide rails | Approximately every two weeks | Clean and lubricate as specified |
| Electrical connections | Periodically | Inspection by qualified personnel |
| Protective covers and interlocks | Before operation | Confirm correct installation and function |
| Machine grounding | During installation and scheduled electrical inspection | Verify by qualified electrician |
Chapter 9. General Troubleshooting Guide
The following table provides general inspection guidance. Do not open electrical compartments or repair high-voltage components unless you are qualified and authorized.
| Problem | Possible Cause | Recommended Action |
|---|---|---|
| No laser output | Cooling protection activated | Check water circulation and cooling system |
| No laser output | Laser power supply or signal fault | Stop the machine and contact qualified service personnel |
| Weak cutting performance | Dirty or damaged optical components | Inspect and clean optics using approved procedures |
| Weak cutting performance | Incorrect focus position | Verify the specified focal distance |
| Excessive smoke inside the machine | Insufficient exhaust airflow | Check the exhaust fan and duct |
| Poor cutting quality | Incorrect processing parameters | Verify speed, power, focus, and material compatibility |
| Abnormal machine noise | Dust, wear, or loose mechanical components | Stop the machine and inspect the affected area |
| Water leakage | Loose or damaged hose connections | Stop operation and repair the cooling circuit before restarting |
| Unstable motion | Guide rail contamination or mechanical wear | Inspect the motion system |
| Machine fails to home | Limit switch, wiring, or motion control issue | Stop operation and contact service personnel |
Warning: Never continue operating the machine when a fault may affect laser safety, electrical safety, cooling, or mechanical movement.
Chapter 10. Technical Information and Service Support
10.1 Reference Electrical Specifications
| Parameter | Reference Value |
|---|---|
| Input Voltage | AC 220V |
| Frequency | 50Hz |
| Reference Rated Power | 1250W |
| Operating Temperature | 5–40°C |
| Relative Humidity | 5–95%, non-condensing |
These are general reference values from the original documentation. Actual specifications vary by machine model, laser power, cooling configuration, and optional accessories.
Always refer to the machine nameplate and the technical specification sheet supplied with the actual equipment.
10.2 Before Contacting Technical Support
Please prepare the following information:
Machine model and serial number
Laser tube type and rated power
Control system model
Description of the problem
Error messages or alarm codes
Photos or videos of the affected components
Recent maintenance or adjustment history
This information helps the technical support team identify the issue more efficiently.
Manufacturer Information
Dongguan Hanlei Laser Equipment Technology Co., Ltd.
Brand: HANLEI
This manual is intended for the installation, operation, and maintenance of compatible HANLEI CO₂ laser cutting machines.
Machine configurations and technical specifications may be updated without prior notice. Please refer to the actual equipment, nameplate, electrical drawings, and model-specific documentation.
Operate safely. Maintain regularly. Follow the manufacturer's instructions.